GLOSSARY OF COMMON ROOFING TERMS:
3-tab shingle: An asphalt shingle comprised of a single layer with the exposed area separated by cut-outs into three tabs that are approximately 12 to 13 inches.
Architectural shingle: An asphalt shingle made up of multiple layers. The tabs on are cut to different sizes and shapes to give the roof a more three-dimensional appearance. Also called dimensional or laminated shingles.
Asphalt shingle: A shingle created by covering a fiberglass mat with an asphalt-based coating, then adding mineral granules to the surface. One of the most common residential roofing materials, it is known for its durability and ease of installation.
Cricket: A device that helps divert water around or away from chimneys and other large roof projections.
Designer shingle: Asphalt roofing shingles with highest-end multidimensional designs made to appear similar to . Often called a “premium” or “luxury” shingles.
Dimensional shingle: Another name for an architectural shingle.
Drip edge: Rigid material that is installed at the edge of the roof to keep shingles off the deck, extending them out over eaves and gutters. This helps control the direction of dripping water that could damage underlying components.
Flashing: A material installed around a roof penetration or along an edge to help keep moisture from seeping into the layers below. Can be found along the roof’s perimeter or at penetrations, walls, expansion joints, valleys, drains, and other places where the roofing is interrupted or terminated.
Laminate shingle: Another name for an architectural shingle.
Ridge cap shingles: Material specifically made to of the roof.
Roof deck protection: Also known as underlayment, these products are often synthetic or fiberglass-reinforced felts. They provide a water-shedding secondary layer of protection under the final roof covering.
Roof ridge vent: An air slot cut into the roof deck at the highest point on the roof. The protects the inside from the weather while allowing air to flow freely through the attic.
Shingle: A piece of roofing material designed to be installed in overlapping rows or courses.
Slope: The steepness of the roof expressed as a ratio. For example, a 4:12 slope means there are 4″ of vertical rise for every 12″ of horizontal length.
Square: A measurement of roof area equal to 100 square feet or enough roofing material to cover 100 square feet of a roof deck.
Starter strip: The that is installed at the edge of the eave. They are also installed along the rakes to improve the wind resistance of the roof.
Tab The bottom portion of a shingle, where the material is separated by the shingle cut-outs.
Valley: The place where two downward-sloping sections of a roof join, creating a “V” shaped depression.
Vapor retarder: A material used to impede the passage or movement of water vapor. Usually included as a layer during roofing installation.
ADDITIONAL ROOFING AND STRUCTURAL TERMS:
Attic vent: An opening that allows air, heat, and water vapor to escape from the attic. This helps prevent damage to roofing materials caused by overheating.
Decking: The structural material over which roofing is applied…usually plywood, boards, or planks.
Dormer: A small, raised roof area protruding from the roof plane, usually housing a window.
Eave: The edge of a roof that overhangs the wall.
Fascia: The wood trim around the perimeter of a building, just under the roofing. Often nailed to the ends of trusses or rafters and used to hang gutters.
Gable roof: A traditional roof style in which two roof planes meet at the ridge line.
Hip roof: A roof with four roof planes coming together at a peak and four separate hip legs.
Ice dam: A mass of ice formed at the roof edge, caused by the refreezing of snow. It can cause ice and water to back up under roofing materials and waterproofing, leading to water damage.
Penetration: Any construction passing through the roofing system, such as vent piping, conduits, and HVAC equipment supports.
Sheathing: The structural material over which roofing is applied. Usually plywood, boards, or planks.
Soffit: The exposed area under a roof eave or overhang.
Vent: An opening that allows air, heat, and water vapor from inside a building to escape to the outside.